Side 1 af 1

Fittings/lynkoblinger..messing eller stål

: 26. nov 2007, 13:06
af Christian
Jeg var i USA i forige uge og købte 230V udgaven af denne pumpe

High Temperature Polysulphone Pump : http://morebeer.com/view_product/17311/102345

Den er foodgrade op til 250 F dvs 120 deg C. Jeg vil bruge pumpen til dels recirkulering under mæskningen og dels til recirkulering under nedkøling af urten med min immersion chiller (se evt http://www.mrmalty.com/chiller.php).

Nu er det så at jeg skal til at vælge slanger og fittings til dette system. Mht. slanger så tror jeg det bliver silicone slanger da de skal kunne holde til kogende urt og være foodgrade.

Mht. fittings regnede jeg med at skulle bruge lynkoblinger i rustfrit stål, men jeg synes ikke det er let at finde nogen egnede. Er det OK at bruge messing fittings såfremt disse renses for overflade bly inden anvendelsen? Er der nogen der har erfaringer med messing fittings? Er det overhovedet nødvendigt med lynkoblinger?

Hvad bruger I andre?
Gode indkøbssteder til fittings osv?

Mvh
Christian

: 26. nov 2007, 18:00
af admin
Det var et nemt :-) http://www.fittings.dk/ den ene af bagmændene bag fredericia bryghus er også fitting mand.

Jens

: 26. nov 2007, 21:59
af Boje
@ Christian
bruge messing fittings såfremt disse renses for overflade bly inden anvendelsen?
Kan du evt. forklae lidt nærmere hvad du mener med det ?
Og hvordan de evt. kunne renses ?

Hilsen Bo

: 27. nov 2007, 08:32
af Christian
Messing er en legering af kobber og zink, men ofte tilsættes også bly for at lette bearbejdningen af materialet.

Fra J.Palmer (http://realbeer.com/jjpalmer/Welding.txt)

"Brass is an alloy of Copper and Zinc with some lead thrown in for
machinability. The lead percentage varies, but for the common brass alloys used in plumbing fittings it is 7% or less. Lead is entirely soluble in
copper, but the presence of zinc changes this. In Brass, the lead exists as
minute globules. These globules act as an intrinsic lubricant during
machining. The result is a micro-thin film of lead being smeared over the
machined surface. It is this lead (a very small amount) that can be
dissolved off by the wort. While this small amount of lead should probably
not be a cause of concern, most people would be happier if it wasn't there
at all.

Well, never let it be said that the Space Program never yields technology
applicable to the home. Some chemists working on the International Space Station Alpha program were consulted for an etchant that could safely remove the lead from the surface of brass parts. The chemists determined that a 1-to-1 volume ratio of Glacial Acetic Acid (98% by vol.) to Hydrogen Peroxide (30% by vol.) would accomplish this without pitting the brass. This procedure was performed in the lab using the standard laboratory concentrations of these chemicals. The process consisted of a 30 second dunk, swirl and rinse at room temperature, and was successful in removing the lead, as determined by a Lead Home Test Kit (swabs). In addition, the procedure had the added benefit of turning the brass into Pure Gold. (Okay, the color of, anyway.)

Because 98% Acetic Acid and 30% Hydrogen Peroxide are not available to the average brewer, the experiment was repeated using the concentrations available in the supermarket. These are 5% Acetic Acid (White Distilled Vinegar) and 3% Hydrogen Peroxide. Due to the difference in concentration, the relative concentration ratio is changed. For the household variety concentrations, a 2-to-1 volume ratio of Acetic Acid to H2O2 is needed.

The process was expected to take longer with the more dilute solution, so
the brass part was immersed for 10 minutes. The results showed the same gold color and the Lead Test swab indicated the lead had been removed. The buttery yellow gold color can be used as an indicator that the process has completed. Home Lead Test kits should be available at most hardware stores.

This procedure for removing surface lead from brass can easily be conducted at home. A 10-15 minute dunk, swirl, and rinse in a 2/1 volume ratio of 5% Acetic Acid and 3% Hydrogen Peroxide has been shown to be effective. By the way, the solution can be irritating to the skin so either wear gloves or use tongs."

: 27. nov 2007, 21:08
af Boje
Takker for info.

Hilsen Bo

: 29. nov 2007, 11:18
af Christian
admin skrev:Det var et nemt :-) http://www.fittings.dk/ den ene af bagmændene bag fredericia bryghus er også fitting mand.

Jens
Hej Jens
Ved du om de handler med private direkte? Det ser umiddelbart ikke sådan ud.
Mvh
Christian

: 29. nov 2007, 16:03
af admin
Jeg har bestilt et katalog, så måske vi kan finde ud af noget :-)

Jens

: 29. nov 2007, 16:41
af johanschledermann
Indkøbssteder!

Prøv http://www.gronsedt.dk
Der har jeg købt haner og fittings i RF-stål

De har leveret meget punktligt og korrekt hver gang!

..og det er ikke dyrt

: 30. nov 2007, 10:31
af Christian
johanschledermann skrev:Indkøbssteder!

Prøv gronsedt.dk
Der har jeg købt haner og fittings i RF-stål

De har leveret meget punktligt og korrekt hver gang!

..og det er ikke dyrt
Det ser ud til at være et godt sted at finde rustfri fittings. Tak for det !