Side 1 af 1

iodophor

: 8. okt 2008, 08:16
af pouljn
hvorfor er der nogle der siger at man ikke må bruge iodophor på kobber,
de bruger det åbenbart til det hele i usa(( Adding one capful (ie 10ml) to 16 litres of water will give a solution of 12.5 ppm of available Iodine. Allow 15 min exposure to sanitise all glass, plastic, copper and stainless steel brewing equipment. Items to be sanitised must be clean before using Iodophor.) ) jeg har kommet til at give min kobber chiller en omgang iodophor før jeg kom den i gryden med urten (havde ikke læst etiketten med småt IKKE KOBBER) er mit øl lige til kloarken nu ,vil ikke byde mig selv eller andre at drikke noget der ikke er i orden :giftig:??? . så hellere lave en ny portion .

håber nogen kan give svar

: 8. okt 2008, 09:24
af skidemajet-inc
Jeg tror det har noget gøre med at det ikke så godt for kobberet, det er vist ikke giftigt. Men måske skulle jeg lade nogen andre, som ved mere, svare på det.

iodophor

: 8. okt 2008, 09:58
af pouljn
man kan håbe det
fandt et til sted



BREWTREE.COM

Counterflow Wort Chiller

Instructions

Thank you for purchasing a Chill Quick Wort Chiller, sure to provide years of dedicated service.

NOTE: THESE CHILLERS ARE NOT DESIGNED TO BE USED WITH PELLET HOPS...ONLY USE WHOLE HOPS OR HOP PLUGS, AND STRAIN THEM OUT (i.e. using a BREWTREE HOPBACK or muslin bag) BEFORE TRANSFERRING WORT THROUGH CHILLER.

Pellet hops disintegrate and turn into a "sludge" that can clog the chiller. If this happens, use a wire to dislodge the hops by running the wire through the copper tubing, then flushing the chiller with water using a high pressure nozzle.

Before Use: Always flush the unit with boiling hot water followed by an iodophor sanitizer. Leave unit full of sanitizer until use, allowing fresh beer to push the iodophor sanitizer out of the unit. Wait until you see that the outflow is 100% wort before transferring to fermentor.

To use: Chiller May be bent for packaging/shipping purposes only, and can easily be re-bent into position. The inlet and outlet ports may also be adjusted by using a hex driver or flat-head screwdriver to remove the clamps, then turning the ports to the desired position. If any resistance is felt, loosen the compression fitting nut that the copper tubing is passing through.

It is always wise procedure to check the unit for leaks before full service. Leaks may be overcome by tightening the clamps and or compression nuts.

Thermometer: The thermometer is fully adjustable. Hold the nut in the back of the unit, while turning the face piece. Watch the dial to line up to the correct temperature. The unit is easily adjusted when placed in boiling water (212 Degrees Fareheit).

We hope you enjoy brewing with our chiller and look forward to seeing you again on ebay, and please feel free to browse our website for great deals www.brewtree.com .

løsning fra brouwland belgien

: 14. okt 2008, 14:44
af pouljn
Copper is a metal which is best cleaned with boiling water. So, if you are using a copper chiller which is to be immersed into the hot wort, your chiller is already sterilised thanks to the hot wort.
Anyway, using a cleaning agent based on acids, such as Iodophor, can corrode the copper little by little (depends of course on the acid dose). So, before your copper chiller is totally loss, you have to clean it many many many times ! So, no problem for your beer though, don't throw it away.
Light power acids can be used sometimes, but always avoid using alcaline agents (s.a. sodium hydroxid) because they will put a black corrosion layer onto the copper.
However, if used moderately, your copper won't suffer too much.